Beatsons Vista Galv Movement Bead 19mm x 3.0m

Plaster and render bead. Designed to be used to form movement joints in plaster or render where long wall runs either have movement joints in situ or where there is a need to allow for differential or thermal movement. The bead consists of two plaster stop lengths joined by a white pvc extrusion which allows for up to 4mm of movement and which is covered by a vinyl tape which is removed after plastering or rendering. Internal use only. We recommend Stainless Steel or PVC-u for external rendering.

Beatsons Soffit Vent Mesh Roll (30 Metres x 75mm)

Beatsons V36 Debonding Sleeves 100mm

Debonding sleeve to allow for movement of the ties listed above (a 25mm wide sleeve is required for channel ties). Debonding sleeves should have a 10mm gap left at end to allow for movement once installed.  

Beatsons VE7 Galv Frame Cramp Ties 200mm

Frame cramp, for restraining masonry to new or existing structures and for building in non-structural elements (frames etc).

Beatsons Green Vapour Barrier 125Mu 4x50m

The purpose of this vapour barrier is to improve airtightness within a building or structure and remove any condensation that might form. It is most commonly used to limit the path of damp, warm air which could otherwise permeate into the roof of a building.

Beatsons Polythene 300Mu/1200g 4x25m Black

300MU Damp Proof Membrane is a low density, blown film of extruded polythene. It is intended for the use with concrete flooring. DPM sheeting can be used as an over-site membrane, being used between a blinded hardcore bed and the base concrete, or as a sandwich membrane between the base and concrete screed or just in base concrete. Black Agrément Certificate  Accredited by the Board of Agrément (BBA: 94/3009) Manufactured using over 90% recycled materials 4m width x 25m length DPM roll coverage: 100m²

Beatsons Polythene Tps 4.5Kg 4 x 25m H/D

Our general-purpose sheeting is produced from recycled material and is manufactured within strict tolerances under ISO 9001, this ensures a high-quality product. A temporary, fully waterproof protection sheet Designed to protect floors and equipment during work Recommended interior use only

Beatsons Damp Proof Course (DPC) 30mtr

DPC provides damp proof protection, preventing the ingress of external moisture. This product is suitable for brick, block, stone or concrete walls. Suitable for vertical and horizontal applications

Beatsons V55 Hand Nail Plate

A nail plate system for manual use which enables the construction of timber structures on site to strengthen joints for non-structural applications. Automated production ensures uniform hole positions.

Beatsons Light Duty Angle Bracket

A multi-purpose fixing angle plate for general site applications, ie for connecting timber joists to timber purlins.

Beatsons Heavy Duty Angle Bracket

A versatile range of brackets for use in 90 degree connections allowing for use of nails, screws and / or bolts and coach screws. Angle Brackets have a reinforced rib.

Beatsons L/D Strap Twist 100

Twisted Light Duty restraint straps are great for any vertical applications, such as attaching wall plates to masonry. These are available in 600mm,900mm and 1200mm. Light duty restraint straps can be used for vertical restraint applications, such as holding down wall plates to masonry. These multi-holed straps are supplied in 100mm increments with 6mm holes at 25mm offset centres. Available straight, bent or twisted or in combinations as required in galvanised or stainless steel.

Beatsons L/D Strap Bend 100

Bent Light Duty restraint straps are great for any vertical applications, such as attaching wall plates to masonry These are available in 600mm,900mm and 1200mm   Light duty restraint straps can be used for vertical restraint applications, such as holding down wall plates to masonry. These multi-holed straps are supplied in 100mm increments with 6mm holes at 25mm offset centres. Available straight, bent or twisted or in combinations as required in galvanised or stainless steel.

Beatsons Light Duty Strap Straight

Light duty restraint straps can be used for vertical restraint applications, such as holding down wall plates to masonry. These multi-holed straps are supplied in 100mm increments with 6mm holes at 25mm offset centres. Available straight, bent or twisted or in combinations as required in galvanised or stainless steel.

Beatsons Masonry Joist Hanger 150 x 50mm

standard hanger is designed for building into brickwork or blockwork.

Beatsons Galv Ext Render Stop/Bellcast Bead 3.0m

Plaster and render bead. Used where a neat drip or ‘bell-end’ lower edge is needed on external render. Fixed by mortar dabs or masonry nails. Although this is for external use we would generally recommend Stainless Steel or PVC-u for this application only using this product in sheltered or low rainfall areas.

Beatsons Galv Plaster Stop Bead 10mm x 3.0m & 13mm x 3.0m

Drylining bead. A bead for protection of thin coat plaster at edges and reveals and for abutment of thin coat plaster against other wall finishes. Also sometimes used as an arch bead. Nail holes for easy fix with drywall nails. Rigid but light bead perforated for an excellent thin coat plaster key. Either 3mm or 6mm Stop. Internal use only.

Beatsons Galv Mini Mesh Bead 3.0m

External bead. Used where a neat drip or ‘bell-end’ lower edge is needed on external render. Fixed by mortar dabs or stainless steel nails.

Beatsons Galv Perforated Thin Coat Bead 3.0m

Drylining Bead.  A thin coat board bead for plaster skimming on plasterboard lined walls. Plaster depth 2/3mm. Nail holes for easy fix with drywall nails. Scalloped edge for an excellent plaster key. Internal use only.

Beatsons Galvanised Angle Bead

Plaster and render bead.  This traditional wet plaster bead provides a strong true corner or arris, with the mesh wings allowing for a good plaster key and resistance to cracking. Fixed by plaster dabs at approximately 600mm centres, push the wings into the dabs to allow for the required plaster depth, up to 13mm, then ensure the nose is set square and plumb as required. Generally for internal use only.

Beatsons Galvanised Fixing Band 20mm x 10mtr

Perforated galvanised band Provides a quick and reliable fixing method Can be cut or bent easily

Beatsons Galv Brick Reinforcement 65mm x 20mtr & 115mm x 20mtr

An expanded metal mesh designed to be incorporated into masonry for crack control. Durability- Excellent corrosion resistance and a service life of not less than 60 years

Beatsons Truss Clip 38mm & 50mm

Attaches trusses and rafters to wall plates to provide wind restraint. Avoids skew nailing damage and provides positive resistance to wind forces. Safe working load 2.38kN uplift.

Beatsons Joist Hanger 50mm & 100mm

Standard Timber to Timber Hangers. A quick and safe method of joist trimming for light, medium and heavy applications such as supporting floor joists, trimming stair wells, and underslung joists. They have increased hole centres to spread load over greater area.

Beatsons Universal Wall Starter C25S 2.3m

The Vista Stainless Steel Wall Starter System joins new walls to existing masonry. Suitable for both internal and external brick or block walls from 60 to 250mm thick, the connectors can be slotted together up to a maximum of 8 metres or 3 storeys high. Stainless Steel Easy connection of new masonry walls 60mm to 250mm wide to existing masonry Pack includes all fixings for a single ski of masonry up to 2400mm high and comes with full instructions. SOLD separate or in a box of 20 (trade pack)